Gate-Mounted Profile
Fasten the stopper directly to the vertical Alumission Gate Frame on the gate itself.
Aluminum Stopper For Gate Frame
0
(0)
Reviews
A dedicated latch-side stopper for Alumission swing-gate frames. It mounts directly to the vertical Gate Frame, creates a clean closing stop, and is the required stopper profile for double swing gates.
Price range: $33.57 through $52.82
The Aluminum Stopper For Gate Frame is the dedicated closing-stop profile for Alumission swing gates. It mounts directly to the vertical Aluminum Gate Frame on the gate itself and creates a straight receiving edge when the gate closes.
For a single swing gate, install the stopper only on the latch side. Do not install it on the hinge side. A hinge-side stopper can create a dangerous finger-pinch point as the gate closes.
For a double swing gate, this is the required stopper profile. It can be mounted on the center vertical frame of either the left or right gate leaf, depending on which leaf should provide the stop for the opposite leaf. It must remain on the meeting/latch edge, never the outer hinge edge.
Order or cut the stopper so its finished length matches the vertical gate frame. A full matching length creates a continuous closing surface and a clean powder-coated finish from the top to the bottom of the gate.
Product Highlights
- Designed for Alumission swing-gate frames
- Attaches directly to the vertical Aluminum Gate Frame
- Latch-side use only on single swing gates
- Do not install on the hinge side
- Required stopper profile for double swing gates
- Can mount on either double-gate leaf at the center meeting edge
- Creates a continuous closing surface
- Length should match the vertical gate frame
- Can be cut to the required gate-frame length
- 6063-T6 aluminum extrusion
- Color-matched powder-coated finishes
Common Applications
- Single swing-gate latch-side stops
- Double swing-gate center meeting stops
- Left-leaf or right-leaf double-gate configurations
- Replacement gate-frame stoppers
- Custom cut-to-length swing-gate fabrication
A Stopper Mounted Directly to the Gate Frame
The profile is part of the moving gate leaf. It is not a wall, post, floor, or ground-mounted stop.
Any Swing-Gate Style
Use it with compatible Alumission single or double swing gates, regardless of the selected slat style.
Not for Sliding Gates
This product is intended for swing-gate closing conditions, not sliding-gate receiving or guide applications.
Match the Frame Length
Use a stopper length equal to the finished vertical gate-frame length for a continuous closing edge.
Never Install the Stopper on the Hinge Side
The stopper belongs on the closing or meeting edge, away from the hinge-side pinch zone.
Single Gate Latch Side
Install the stopper on the vertical gate frame at the latch side of a single swing gate.
Keep the Hinge Side Clear
Do not place the stopper on the hinge side, where a closing gate can trap fingers between moving parts.
Closing Surface
Position the profile so the gate closes against the raised stop without interfering with the latch hardware.
Check Clearances
Verify the final gap, latch engagement, gate travel, and safe hand clearances before use.
The Required Stopper for Two Meeting Gate Leaves
At the center of a double gate, the stopper gives one leaf a defined receiving edge for the opposite leaf.
Center Meeting Edge
Install the stopper on the center vertical Gate Frame where the two swing-gate leaves meet.
Either Gate Leaf
Mount it on either the left or right leaf, depending on the planned closing sequence and latch arrangement.
One Leaf Stops the Other
The stopper creates the contact edge that positions the opposite leaf when the double gate is closed.
Full Vertical Length
Match the stopper to the vertical frame length for a clean and consistent center seam.
Included: One Aluminum Stopper For Gate Frame in the selected length and powder-coated finish.
Sold separately: Aluminum Gate Frame, Slide Side Cover For Gate Frame, slats, screws, hinges, latch or lock hardware, drop rods, caps, reinforcement, and other gate installation hardware.
Phone-order lengths: 10′ lengths are available by phone order only. They cannot be purchased online, and shipping charges may apply.
Aluminum Stopper For Gate Frame
Profile dimensions and gate-frame installation detail for the dedicated latch-side and double-gate meeting stopper.
Overall width
1.750″
Overall height
0.750″
Raised stop width
1.031″
Raised stop height
0.245″
Profile thickness
0.070″
Compatible gate type
Single and double swing gates
Mounting location
Directly to the vertical Aluminum Gate Frame
Single-gate position
Latch side only
Double-gate position
Center meeting edge of either gate leaf
Finished length
Match the vertical gate-frame length
Material
6063-T6 aluminum
Weight
Approximately 0.430 lb/ft
Online lengths
6′ and 8′
Phone-order length
10′
Finishes
Black, Bronze, White, Dark Grey, Light Gray
Installation note: Mount the stopper only to the gate frame at the latch or center meeting edge. Never install it on the hinge side. Verify gate travel, closing sequence, latch engagement, safe clearances, and complete assembly requirements before installation.
Aluminum Stopper For Gate Frame Questions & Answers
Answers about swing-gate compatibility, latch-side placement, hinge-side safety, double-gate use, frame attachment, stopper length, dimensions, ordering, and care.
Purpose & Compatibility
What is the Aluminum Stopper For Gate Frame used for?
It creates a defined closing surface on an Alumission swing gate. The stopper mounts directly to the vertical gate frame on the latch or center meeting side.
Can it be used on a single swing gate?
Yes. Install it on the vertical Gate Frame at the latch side of the single swing gate.
Can it be used on a double swing gate?
Yes. This is the required stopper profile for an Alumission double swing gate. It creates the center stop where the two gate leaves meet.
Can it be used with any Alumission swing-gate style?
Yes, when the swing gate uses the compatible Alumission Aluminum Gate Frame. The selected slat style does not change the stopper location.
Can it be used on a sliding gate?
No. This stopper is intended for swing-gate closing and meeting conditions.
Does it attach to a wall, post, or the ground?
No. It attaches only to the gate itself, directly on the vertical Aluminum Gate Frame.
Placement & Safety
Which side of a single swing gate should receive the stopper?
Install it only on the latch side, where the gate closes against the receiving condition.
Can I install the stopper on the hinge side?
No. Do not install it on the hinge side. The closing gate can create a dangerous finger-pinch point between the stopper and the surrounding frame or structure.
Why is hinge-side installation dangerous?
The hinge side has changing clearances as the gate moves. Adding a raised stopper there can create a place where fingers may be trapped during closing.
Does the stopper replace the gate latch or lock?
No. The stopper creates the closing surface. The compatible latch, lock, strike, drop rod, or other securing hardware is selected separately.
Should the gate clearances be checked after installation?
Yes. Verify the full opening and closing travel, latch engagement, stopper contact, ground clearance, and safe hand clearances before using the gate.
Double Swing Gates
Where is the stopper installed on a double swing gate?
Install it on the center vertical Gate Frame where the two gate leaves meet.
Can the stopper be installed on either double-gate leaf?
Yes. It can be installed on the center edge of either the left or right leaf, depending on the planned closing sequence and latch arrangement.
Does either side mean I can put it on a hinge edge?
No. Either side refers to choosing the left or right gate leaf at the center meeting edge. Never install the stopper on an outer hinge edge.
How does the stopper work on a double gate?
The stopper on one leaf creates a receiving edge that positions the opposite leaf when the two gates close together.
Is another type of stopper recommended for Alumission double gates?
No. This is the dedicated Alumission stopper profile for double swing gates built with the compatible Gate Frame.
Should the closing sequence be planned before mounting it?
Yes. Decide which leaf closes first, where the latch or drop rod will be located, and which leaf should carry the stopper before drilling or fastening.
Length, Dimensions, Ordering & Care
How long should the stopper be?
Its finished length should match the vertical gate-frame length.
Can the stopper be cut to length?
Yes. Cut it with suitable aluminum-cutting equipment, measure carefully, and deburr the cut end before installation.
What are the main profile dimensions?
The profile is 1.750″ wide and 0.750″ high. The raised stop is 1.031″ wide and 0.245″ high, and the profile thickness shown is 0.070″.
What is included with this product?
The product includes one Aluminum Stopper For Gate Frame in the selected length and powder-coated finish.
Are the Gate Frame and installation hardware included?
No. The Gate Frame, side cover, slats, screws, hinges, latch or lock hardware, drop rods, caps, reinforcement, and other gate components are sold separately.
What lengths are available online?
The online length options are 6′ and 8′.
Is a 10′ length available?
Yes. The 10′ length is available by phone order only. It cannot be purchased online, and shipping charges may apply.
What colors are available?
Available finishes are Black, Bronze, White, Dark Grey, and Light Gray.
Will a cut edge rust?
No. Aluminum does not rust like steel.
How should the powder-coated finish be cleaned?
Clean with mild soap and water using a soft cloth or sponge. Avoid abrasive pads, harsh chemicals, and strong solvents.
Reviews
There are no reviews yet.