What is this cane bolt used for?

It is recommended for securing the inactive leaf of an unmotorized Alumission double swing gate by lowering the rod into a compatible ground receiver.

Can I use it on a single swing gate?

The manufacturer supports gate and door applications, but Alumission recommends this 12″ configuration primarily for the inactive leaf of a double swing gate. Confirm compatibility with your specific design before installation.

Are the Black and Silver versions the same size and material?

Yes. Both variations are 1/2″ × 12″ steel cane bolts; only the finish differs.

Which finish should I choose?

Choose Black to coordinate with black powder-coated gate components or Silver for a clean natural-metal appearance.

Do both finishes cost the same?

Yes. Black and Silver are both $45.15.

Where should it be installed?

Install it vertically on the inactive gate leaf near the center meeting edge and align it with a compatible receiver in the ground or concrete.

How does the hold-open position work?

Lift the L-shaped handle and rotate it into the guide bracket’s hold-open position to keep the rod raised.

Can it be installed horizontally?

Yes. The manufacturer supports vertical or horizontal mounting, although vertical installation is recommended for Alumission double swing gates.

Is the hardware weather resistant?

The manufacturer specifies WeatherGuard Protection for the black finish. Inspect outdoor hardware periodically and maintain it as needed for the installation environment.

Can it be used on an automated gate?

This cane bolt is intended for unmotorized operation. For an automated gate, consult a qualified installer to ensure it cannot conflict with the operator or gate travel.

Black 12-inch heavy-duty steel cane bolt kit with two brackets and four mounting screws

Black 12-inch cane bolt mounted on the inactive leaf of an Alumission aluminum double swing gate

12″ Heavy-Duty Gate Cane Bolt for Double Swing Gates

0 (0) Reviews

Heavy-duty 1/2″ × 12″ steel cane bolt for securing the inactive leaf of an Alumission double swing gate. Available in Black or Silver with mounting brackets and screws included.

STARTING AT $45.15

Color

Clear

WHAT’S INCLUDED:

One 1/2″ × 12″ steel cane bolt, two guide/receiver brackets, and four mounting screws in the selected Black or Silver finish.

Box Weight

Box Dimension

TECHNICAL SPECIFICATIONS & INSTALLATION

This 12″ heavy-duty steel gate cane bolt is designed to secure the inactive leaf of an unmotorized double swing gate. Mounted vertically to the gate frame, the 1/2″-diameter drop rod lowers into a compatible ground receiver to help keep the gate firmly positioned.

The L-shaped handle makes the bolt easy to lift and rotate, while the guide brackets keep the rod aligned and provide a convenient hold-open position. Choose Black to coordinate with black Alumission gates or Silver for a clean natural-metal appearance. Mounting hardware is included.

Questions & Answers

Find clear answers about Wall Topper sizing, 6-foot spans, included components, base-plate installation, concealed fasteners, style differences, finishes, maintenance and field fitting.

Sizing & Planning

What span is the aluminum Wall Topper designed for?

Each Wall Topper section is designed around a nominal 6-foot span between posts. The supplied horizontal slats are 6 feet long. Verify the actual field measurement before cutting, and plan one post per span plus one terminal post at the end of the run.

Which Wall Topper heights are available?

All five Wall Topper styles are offered in seven nominal heights: 1 foot, 1 foot 6 inches, 2 feet, 2 feet 6 inches, 3 feet, 3 feet 6 inches, and 4 feet. Select the height that fits the project, then review the exact style-specific material schedule shown on the product page.

How do I plan a multi-span Wall Topper run?

Divide the finished run into nominal 6-foot sections. Use one post for each span and add one terminal post at the end of the run. Confirm corners, end conditions, wall steps, field cuts, post locations, and local requirements before ordering.

How do I measure an existing wall for a Wall Topper?

Measure the total finished run, each individual wall section, corners, steps, end conditions, and the usable mounting surface. Mark proposed post locations and check for caps, slopes, drains, utilities, or other obstructions. Use actual field measurements—not only nominal wall dimensions—before ordering or cutting.

Can the 6-foot Wall Topper slats be cut for a shorter span?

Yes. The aluminum slats are supplied in 6-foot lengths and may be field cut to fit a shorter verified opening. Use suitable cutting equipment, keep cuts square, remove burrs, protect the finish, and confirm the finished post-to-post dimension before cutting.

Kit Contents & Style Options

What is included with an Alumission Wall Topper kit?

The selected kit includes Aluminum Post 2 Channels, two channel covers and one cap per post, an 18-inch zinc-coated steel post base and matching aluminum base cover per post, 6-foot aluminum slats in the selected style and height, the required pattern spacers where applicable, and stainless steel self-drilling assembly screws. Wall anchors are not included because the correct fastener depends on the wall material and project conditions.

How do Dallas, Los Angeles, Miami, New York, and San Francisco styles differ?

Dallas combines wide 5.5-inch slats with a four-slat 1-inch accent band. Los Angeles uses evenly spaced 5.5-inch slats. Miami centers a four-slat 1-inch accent band between wide slats. New York is a tight-stacked full-privacy design with size-specific finishing slats. San Francisco uses closely spaced 1-inch slats for a linear look. See the exact material schedule and proportional drawings on each style page.

Is the Wood finish real wood?

No. The Wood option is a wood-look finish applied to aluminum slats, not natural timber. It provides the warmth of a wood appearance while keeping the low-maintenance, noncombustible aluminum construction of the Wall Topper system.

How much privacy does an aluminum Wall Topper add?

Privacy depends on the selected style, height, slat sizes, and spacing. New York is the most closed design, while Dallas, Los Angeles, Miami, and San Francisco create different levels of screening and visibility. Compare the style-specific drawings and material schedule before choosing.

Installation & Mounting

How do the base plate and base cover work?

Each post uses a zinc-coated steel base with a 4-inch by 4-inch plate and an 18-inch stem. The plate is anchored to a structurally suitable wall, the aluminum base cover slides over the plate to conceal the mounting screws or anchors, and the aluminum post slides over the steel stem. Plumb and align every post before installing the slats.

Can the Wall Topper be installed on concrete, masonry, wood, or steel?

Installation may be possible on concrete, masonry, properly reinforced wood, steel, or another structurally suitable wall when the correct substrate-specific anchors are used. Anchors are not included. The installer is responsible for confirming wall condition, edge distances, waterproofing, fastener selection, wind exposure, loads, and code or permit requirements.

Are anchors for the existing wall included?

No. Wall anchors are not included because the correct fastener and embedment depend on the wall material, wall condition, edge distances, loads, and site exposure. Select an anchor system specifically approved for the actual substrate and project conditions.

How do I know whether my wall can support a Wall Topper?

The existing wall and its foundation must be structurally suitable for the planned topper, anchors, height, and site loads. Inspect the wall for cracks, loose caps, deterioration, insufficient thickness, or other damage. When suitability is uncertain, have a qualified contractor or design professional evaluate it before installation.

Care, Ordering & Support

Does the Wall Topper require welding?

No welding is required for the kit assembly. Installation is a mechanical field-fit process that requires accurate measuring, cutting, drilling, leveling, fastening, and anchoring. Channel covers snap into place after assembly to conceal the slat-fastening screws.

Which finishes are available, and how should the Wall Topper be maintained?

Current finish options may include Black, Bronze, White, Dark Grey, Light Gray, and Wood. Availability can change by configuration. Clean powder-coated aluminum with water, mild soap, and a soft cloth; avoid abrasive pads, harsh chemicals, and tools that can scratch the finish.

What should I verify before ordering?

Confirm the total run length, selected style and height, number of 6-foot spans, post and terminal locations, corners or steps, wall construction, anchor plan, finish, field-cut requirements, access, wind exposure, and local rules. Product drawings support selection and installation planning but are not stamped structural or permit drawings.

Can a Wall Topper follow a stepped or sloped wall?

A stepped wall can often be planned as separate level sections with post locations and field cuts coordinated at each change in elevation. A continuously sloped wall requires a custom layout. Measure every section carefully and confirm the proposed arrangement with Alumission before ordering.

Do I need a permit or HOA approval for a Wall Topper?

Requirements vary by location and property. Check local height limits, setbacks, wind and structural rules, permit requirements, easements, and any HOA or architectural-review standards before ordering or installing. The product drawings are planning references, not stamped permit or structural drawings.