Designed for the 6″ Snap Slat
The profile is made specifically to finish the compatible 6″ Aluminum Snap Slat system, so the top member follows the same broad architectural face and full-privacy layout.
6″ Aluminum Top Snap Slat 8′
0
(0)
Reviews
The 8-foot finishing top snap slat for compatible 6-inch FenceOn privacy panels. Available in Black and White.
$51.00
6″ Aluminum Top Snap Slat 8′ is the finishing profile made specifically for the compatible 6″ Aluminum Snap Slat full-privacy system. It snaps into the final standard slat to close the assembly and create a flat, clean top edge.
The broad, flat face keeps the top of the fence or gate square and visually complete, eliminating the open snap edge that would remain if the panel ended with a standard slat.
Use it as the top finishing member for full-privacy fences, screens, swing gates, sliding gates, and pedestrian gates built with the 6″ Aluminum Snap Slat 8′.
Designed for back and side yards, commercial properties, industrial facilities, equipment screens, and service areas where privacy, durability, and low maintenance matter.
Manufactured from 6063-T6 aluminum, the profile has a noncombustible aluminum body and can be a practical component in projects using noncombustible fencing near structures, including zone 0 planning. The slat is not by itself a certified fire-rated assembly; final compliance depends on the complete system design, connections, clearances, adjacent materials, and local requirements.
When snapped into the matching full-privacy panel, the top member closes and aligns the assembly. Because a solid privacy panel can experience greater wind pressure than an open fence, posts, frames, fasteners, spans, footings, and the complete assembly must be sized for the site wind loads.
Product Highlights
- Purpose-built top member for the compatible 6″ Aluminum Snap Slat system
- Snaps into the final standard slat
- Creates a clean, flat, square top edge
- Closes the top of a full-privacy panel
- Suitable for fences, screens, and gate assemblies
- 6063-T6 aluminum construction
- Exterior powder-coated finish
- Noncombustible aluminum body for fire-conscious and zone 0 planning
- Corrosion resistant and low maintenance
- Available in Black or White in an 8′ length
Common Applications
- Top edge of full-privacy backyard fences
- Side-yard privacy fences and screens
- Commercial privacy and security screens
- Industrial and equipment enclosures
- Sliding gate panels
- Swing and pedestrian gates
- Noncombustible fence and gate planning in zone 0, subject to local requirements
- Wind-exposed projects when the complete assembly is properly engineered
Snaps In for a Flat, Square Top
This purpose-built finishing member closes the final course of the compatible 6″ snap-slat system, giving the completed fence or gate a straight, finished upper edge.
Secure Snap Connection
Its formed snap edge engages the matching edge of the final standard slat, helping keep both profiles aligned as part of the surrounding frame and support system.
Flat, Closed Top Edge
The smooth upper face closes the open interlocking edge that would remain at the top of a panel finished with a standard snap slat.
Clean and Square Appearance
The finishing profile gives fences, privacy screens, and gate panels a straight, visually complete top line without changing the continuous full-privacy surface.
Privacy, Fire-Conscious Planning, and Wind Design
The top snap slat completes full-privacy assemblies used across residential, commercial, and industrial projects while supporting durable, low-maintenance material selection.
Backyards and Side Yards
Use it to finish privacy fencing around patios, pools, side passages, outdoor living areas, and residential property lines.
Commercial and Industrial Screening
A practical finishing member for equipment screens, service areas, storage zones, security boundaries, industrial enclosures, and full-privacy gates.
Fire-Conscious zone 0 Planning
The aluminum body is noncombustible and can support projects using noncombustible fencing near structures, including zone 0 planning. The complete installation and local requirements must still be verified.
Wind-Load Planning
A solid privacy panel can receive greater wind pressure than an open fence. Posts, frames, reinforcement, fasteners, spans, and footings must be sized for the complete assembly and site wind loads.
Included: One 8′-long 6″ Aluminum Top Snap Slat in the selected Black or White finish.
Sold separately: Standard 6″ Aluminum Snap Slats, posts, gate frames, channels, screws, caps, brackets, reinforcement, and other installation hardware.
6″ Aluminum Top Snap Slat 8′
Proportional profile dimensions, snap-edge construction, material, finish, length, and compatible full-privacy applications.
Overall profile size
6.000″ × 0.803″
Wall thickness
0.053″ typical
Profile function
Top finishing member for the compatible 6″ snap-slat system
Privacy
Full privacy when used with the matching system
Material
6063-T6 aluminum
Finish
Exterior powder coated
Online length
8′
Available finishes
Black and White
Installation orientation
Top finishing member in a compatible horizontal panel assembly
Fire and defensible space
Noncombustible aluminum body; suitable for zone 0 planning subject to complete-system and local requirements
Wind
Complete assembly must be designed for the site wind loads
Planning note: Dimensions are nominal and normal extrusion tolerances apply. Confirm the complete snap-slat assembly, finished opening, support, fasteners, site wind loads, and local zone 0 or fire requirements before fabrication.
Everything You Need to Know
Helpful answers about applications, dimensions, compatibility, installation, finishes, ordering, and care.
Product & System Fit
What is the 6″ Aluminum Top Snap Slat?
It is the finishing profile for the compatible 6″ Aluminum Snap Slat system. It snaps into the final standard slat and provides a flat, closed top edge.
Is this the same as the standard 6″ Aluminum Snap Slat?
No. The standard slats interlock to build the main full-privacy panel. This top snap slat is the finishing member used at the top of that assembly.
How does the top snap slat connect?
Its formed snap edge engages the matching edge of the final compatible 6″ Aluminum Snap Slat. The completed panel should also be retained by the appropriate frame or support system.
Why does the top slat have a flat edge?
The flat edge closes the open interlocking profile at the top, keeps the finished panel square, and creates a clean architectural appearance.
Does it create full privacy?
Yes. When used with the matching 6″ Aluminum Snap Slats in a properly assembled panel, it completes a continuous full-privacy surface.
How many top snap slats do I need?
Typically, one continuous top member is used for each fence or gate section and cut to the required finished width.
Can it be used with another slat size?
It is designed specifically for the compatible 6″ Aluminum Snap Slat system. Do not assume fit with a different profile or size; verify compatibility before ordering.
Applications & Installation
Where is this top snap slat commonly used?
It is used to finish full-privacy fences, screens, swing gates, sliding gates, and pedestrian gates in back yards, side yards, commercial properties, and industrial facilities.
Is it suitable for commercial and industrial projects?
Yes. It is suitable for privacy screens, equipment enclosures, service areas, security boundaries, and gate panels when the complete system is designed for the application.
Is this profile installed horizontally or vertically?
It is primarily intended as the top finishing course of a horizontal 6″ snap-slat panel. Verify the system detail before using it in another orientation.
Can the 8′ profile be cut?
Yes. Cut it with suitable aluminum-cutting equipment and a fine-tooth blade, then deburr the cut edge before assembly.
What is included?
One 8′-long 6″ Aluminum Top Snap Slat in the selected Black or White finish.
Are the standard slats and installation hardware included?
No. Standard 6″ Aluminum Snap Slats, posts, frames, channels, screws, caps, brackets, reinforcement, and other installation hardware are sold separately.
How should the finish be maintained?
Wash with mild soap and water using a soft cloth or sponge. Avoid abrasive pads and harsh chemicals that can damage the powder-coated surface.
Fire, zone 0 & Wind
Is the profile noncombustible?
The aluminum body is noncombustible and does not provide fuel in the way wood fencing can. Performance of the finished installation still depends on coatings, adjacent materials, gaps, connections, and the complete assembly.
Can it be used in zone 0?
It can be a practical material choice for noncombustible fencing and gate projects in zone 0. Always verify the complete design, required clearances, connections to structures, and current local or state requirements before installation.
Is this a certified fire-rated product?
No fire-resistance rating is claimed for this individual profile. A fire rating applies to a tested complete assembly, not to one aluminum component by itself.
Does the full-privacy surface stop embers or flame?
The continuous solid surface reduces open gaps compared with an open fence, but it is not a guarantee against ember or flame passage. Fire performance depends on the complete installed system and surrounding conditions.
Is the completed panel wind resistant?
The aluminum profile is strong and corrosion resistant, but a solid full-privacy panel catches more wind than an open fence. Wind resistance depends on panel width and height, posts, frames, reinforcement, fasteners, footings, exposure, and local wind loads.
What is required for a high-wind installation?
Have the complete fence or gate assembly sized for the site conditions. Post spacing, frame size, internal reinforcement, fasteners, footings, gate hardware, and allowable spans may all need adjustment.
Reviews
There are no reviews yet.