Exact Compatibility
Use this cap only with the Alumission Aluminum Side Post.
The Aluminum Cap For Side Post is designed only for the Alumission Aluminum Side Post. It closes the open ends of the profile and provides a clean, finished appearance.
Each side post should receive a cap on both the top and bottom. The cap measures 1.75″ × 2.125″, is 1/16″ thick, and is manufactured from 6061-T6 aluminum.
Four mounting holes allow the cap to be mechanically secured with suitable #8 screws or 1/8″ aluminum rivets.
The rectangular plate follows the proportions of the Alumission Aluminum Side Post and closes its open end.
Use this cap only with the Alumission Aluminum Side Post.
Install one cap on the top of the side post for a clean finished end.
Install a second cap on the bottom of the side post to close the lower end.
Do not substitute this cap for caps designed for the Post 2 Channels, Post 3 Channel, or Gate Frame.
The cap is proportioned to match the Side Post profile and manufactured from durable aluminum.
The cap measures 1.75″ across its shorter side.
The cap measures 2.125″ across its longer side.
The aluminum plate is 1/16″ thick.
The cap is manufactured from 6061-T6 aluminum.
Four pre-positioned mounting holes support a secure mechanical connection to the post.
Make sure the post end is square, clean, and free of burrs before positioning the cap.
Suitable #8 screws can be used through the four mounting holes.
Use 1/8″ aluminum rivets when a riveted connection is preferred.
Center the cap over the post end and keep it aligned while installing the fasteners.
Included: One Aluminum Cap For Side Post in the selected finish.
Sold separately: Aluminum Side Post, #8 screws, 1/8″ aluminum rivets, bases, reinforcement, anchors, slats, post covers, and other installation components.
Dimensions, material, compatibility, mounting-hole, and fastening information for the 6061-T6 cap used on the Alumission Aluminum Side Post.
Dimensions are nominal and shown in inches. The cap measures 1.75″ × 2.125″ and is made from 1/16″-thick 6061-T6 aluminum. Install one cap on the top and one on the bottom of each Side Post.
Answers about Side Post compatibility, top and bottom use, dimensions, 6061-T6 aluminum, fastening, finishes, ordering, and care.
It closes and finishes the open end of the Alumission Aluminum Side Post.
This cap is designed only for the Alumission Aluminum Side Post.
No. Use the cap designed for the exact Alumission post profile.
No. The Gate Frame requires its own compatible cap.
Yes. Its 1.75″ × 2.125″ rectangular proportions are designed for the Aluminum Side Post.
Yes. Install one cap on the top end of the Side Post.
Yes. Each Side Post should also receive a cap on its bottom end.
Use two caps per Side Post: one on top and one on the bottom.
Yes. The same Aluminum Cap For Side Post can be used on the top or bottom.
Fit and secure the caps as part of final post assembly when the post ends are clean and properly aligned.
The cap measures 1.75″ by 2.125″.
The aluminum plate is 1/16″ thick.
It is made from 6061-T6 aluminum.
The cap has four round mounting holes, one near each corner.
Yes. Suitable #8 screws can be used through the four mounting holes.
Yes. Use 1/8″ aluminum rivets when a riveted connection is preferred.
Available powder-coated finishes are Black, Bronze, White, Dark Grey, and Light Gray.
Select the same powder-coated finish as the Side Post for a coordinated appearance.
No. #8 screws and 1/8″ aluminum rivets are sold separately.
No. Aluminum does not rust like steel.
Use mild soap and water with a soft cloth or sponge. Avoid abrasive pads, harsh chemicals, and strong solvents.
Discussions
There are no questions yet.