
A Site Survey Checklist Before Ordering Aluminum Fence and Gate Kits
Map fence runs, measure openings and record mounting conditions before selecting aluminum fence and gate kits.
THE ALUMISSION JOURNAL
An aluminum gate kit order starts with more than a style and an opening measurement. For a contractor, the useful question is: Which parts are in this exact selection, and who is responsible for everything else?
Before placing the order, build a short materials and responsibility list. Keep the selected product variation, site notes, and current instructions together so the person ordering and the person installing are working from the same information.
Measure the finished opening between the mounting surfaces at the top, middle, and bottom. Record the narrowest width, desired height, mounting surfaces, hinge side, latch position, and intended swing direction. Check for steps, landscaping, equipment, or changes in grade along the swing path. Review Alumission’s opening-planning guide.
Use those notes when you compare single swing gate kits. If a double swing gate is under consideration, sketch both leaves and their meeting point rather than treating the project as one wider single leaf. Ask the client how the opening will be used and where each leaf needs to stop.
For the Miami Style single swing kit, listed sizes describe maximum fitting limits, not the size of a preassembled gate leaf. Check the Miami product page. Review the illustrated instructions before cutting, and ask Alumission to check the selection if the fit is unclear.
Select the intended size and finish before checking contents. On the Los Angeles single swing product page, the selected variation’s included-items list identifies items, quantities, supplied lengths, and finishes. Open the product page and expand the packing list for the actual selection; do not rely on a list saved for a different size or finish.
Transfer the details into a job worksheet. Give each item a status: included in the selected kit, to be supplied separately, or still to be confirmed. Record the variation link and the date you checked it, then share the worksheet with whoever will receive and install the order.
For each line, check the description as well as the count. A supplied length is useful for inventory, but it should not be treated as an approved cut length. Use the current instructions and the measured opening to prepare the cut plan for the selected product.
The Los Angeles single swing product page lists aluminum slats, gate-frame profiles, side posts, hinges, a keyed entry lever, and assembly hardware as kit contents. Check the Los Angeles product page and the selected variation for the actual included hardware. Confirm unclear details before placing the order.
The side-yard gate page identifies tools, anchors suited to the mounting surface, site preparation, and installation labor as items for the buyer to provide. Read the side-yard gate guide. Use that as a prompt to assign responsibility, not as a substitute for the selected product’s packing list. Ask:
If a line is ambiguous, send Alumission the variation link, opening measurements, and photos. Write the answer into the worksheet before purchasing additional parts or committing to the installation plan.
The New York Style double swing kit is listed with components for two leaves, including aluminum frames and slats, side posts, hinges, a keyed lever, and a cane bolt. Its selected-variation packing list describes the complete two-leaf kit. Review that product’s list rather than doubling a single-gate list.
For a double swing layout, identify the hinge side of each leaf, the center meeting point, and the intended access pattern. On the Miami Style double swing product page, Alumission calls for a separate cut plan for both leaves and their center meeting point. Review the double-swing planning guidance. Check the current instructions for the actual product and confirm both leaf dimensions before cutting.
Before ordering, give the client or project lead the variation link and the worksheet. Resolve open questions about finish, included hardware, mounting supplies, and responsibility for site work. Keep the final selection and any clarification with the project record.
When the components arrive, compare them with the selected packing list before cutting or drilling. Check item names, quantities, supplied lengths, and finish; document any discrepancy and resolve it before proceeding. Revisit the site measurements and current instructions before making irreversible cuts.
Ready to check a selection? Explore gate kits, then open the intended variation and verify its packing list against the job worksheet before ordering.
Explore products, installation resources, and advice from our team.
More ideas and practical guidance for your outdoor project.

Map fence runs, measure openings and record mounting conditions before selecting aluminum fence and gate kits.

A practical handover checklist for contractors, covering installed components, measurements, client instructions and unresolved work.

Choose gate access hardware around everyday use, then confirm fit, exposure, and installation requirements for your specific project.
Fill out the details below and we’ll get back to you shortly!